Standards and Units
As we learned in Section 1.1, physics is an experimental science. Experiments require measurements, and we generally use numbers to describe the results of measurements. Any number that is used to describe a physical phenomenon quantitatively is called a physical quantity. For example, two physical quantities that describe you are your weight and your height. Some physical quantities are so fundamental that we can define them only by describing how to measure them. Such a definition is called an operational definition. Two examples are measuring a distance by using a ruler and measuring a time interval by using a stopwatch. In other cases we define a physical quantity by describing how to calculate it from other quantities that we can measure. Thus we might define the average speed of a moving object as the distance traveled (measured with a ruler) divided by the time of travel (measured with a stopwatch).
When we measure a quantity, we always compare it with some reference standard. When we say that a Ferrari 458 Italia is 4.53 meters long, we mean that it is 4.53 times as long as a meter stick, which we define to be 1 meter long. Sucha standard defines a unit of the quantity. The meter is a unit of distance, and the second is a unit of time. When we use a number to describe a physical quantity, we must always specify the unit that we are using; to describe a distance as simply “4.53” wouldn’t mean anything.
To make accurate, reliable measurements, we need units of measurement that do not change and that can be duplicated by observers in various locations. The system of units used by scientists and engineers around the world is commonly called “the metric system,” but since 1960 it has been known officially as the International System, or SI (the abbreviation for its French name, Système International). Appendix A gives a list of all SI units as well as definitions of the most fundamental units.
Time
From 1889 until 1967, the unit of time was defined as a certain fraction of the mean solar day, the average time between successive arrivals of the sun at its highest point in the sky. The present standard, adopted in 1967, is much more precise. It is based on an atomic clock, which uses the energy difference between the two lowest energy states of the cesium atom (133Cs). When bombarded by microwaves of precisely the proper frequency, cesium atoms undergo a transition from one of these states to the other. One second (abbreviated s) is defined as the time required for 9,192,631,770 cycles of this microwave radiation (Fig. 1.3a).
Length
In 1960 an atomic standard for the meter was also established, using the wavelength of the orange-red light emitted by excited atoms of krypton 186Kr2. From this length standard, the speed of light in vacuum was measured to be 299,792,458 m>s. In November 1983, the length standard was changed again so that the speed of light in vacuum was defined to be precisely 299,792,458 m>s.Hence the new definition of the meter (abbreviated m) is the distance that light travels in vacuum in 1>299,792,458 second (Fig. 1.3b). This modern definition provides a much more precise standard of length than the one based on a wavelength of light.
Mass
The standard of mass, the kilogram (abbreviated kg), is defined to be the mass of a particular cylinder of platinum–iridium alloy kept at the International Bureau of Weights and Measures at Sèvres, near Paris (Fig. 1.4). An atomic standard of mass would be more fundamental, but at present we cannot measure masses on an atomic scale with as much accuracy as on a macroscopic scale. The gram (which is not a fundamental unit) is 0.001 kilogram.
Other derived units can be formed from the fundamental units. For example, the units of speed are meters per second, or m>s; these are the units of length (m) divided by the units of time (s).
Unit Prefixes
Once we have defined the fundamental units, it is easy to introduce larger and smaller units for the same physical quantities. In the metric system these other units are related to the fundamental units (or, in the case of mass, to the gram) by
multiples of 10 or 1 10 Thus one kilometer 11 km2 is 1000 meters, and one centimeter 11 cm2 is 1
100 meter. We usually express multiples of 10 or 1 10 in exponential notation: 1000 = 103, 1
1000 = 103, and so on. With this notation, 1 km = 10m3 and 1 cm = 10m2.
The names of the additional units are derived by adding a prefix to the name of the fundamental unit. For example, the prefix “kilo-,” abbreviated k, always means a unit larger by a factor of 1000; thus
1 kilometer = 1 km = 103meters = 103 m
1 kilogram = 1 kg = 103 grams = 103 g
1 kilowatt = 1 kW = 103 watts = 103 W
A table in Appendix A lists the standard SI units, with their meanings and abbreviations.
Table 1.1 gives some examples of the use of multiples of 10 and their prefixes with the units of length, mass, and time. Figure 1.5 shows how these prefixes are used to describe both large and small distances.
The British System
Finally, we mention the British system of units. These units are used in only the United States and a few other countries, and in most of these they are being replaced by SI units. British units are now officially defined in terms of SI units, as follows:
Length: 1 inch = 2.54 cm (exactly)
Force: 1 pound = 4.448221615260 newtons (exactly)
The newton, abbreviated N, is the SI unit of force. The British unit of time is the second, defined the same way as in SI. In physics, British units are used in mechanics and thermodynamics only; there is no British system of electrical units. In this book we use SI units for all examples and problems, but we occasionally give approximate equivalents in British units. As you do problems using SI units, you may also wish to convert to the approximate British equivalents if they are more familiar to you (Fig. 1.6). But you should try to think in SI units as much as you can.
Frequently Asked Questions
Recommended Posts:
- finding and using the Center of gravity
- solving rigid-body equilibrium problems
- SOLVED EXAMPLES ON EQUILIBRIUM
- stress, strain, and elastic moduLi
- tensile and Compressive stress and strain
- Bulk stress and strain
- Shear Stress and Strain
- eLastiCitY and pLastiCitY
- Summary of equilibrium and elasticity
- Fluid Mechanics
- GASES LIQUID AND DENSITY
- Pressure in a fLuid
- pressure, depth, and pascals Law
- PASCAL LAW
- absolute Pressure and Gauge Pressure