Digital Circuits - Shift Registers

We know that one flip-flop can store one-bit of information. In order to store multiple bits of information, we require multiple flip-flops. The group of flip-flops, which are used to hold store????? the binary data is known as register.

If the register is capable of shifting bits either towards right hand side or towards left hand side is known as shift register. An ‘N’ bit shift register contains ‘N’ flip-flops. Following are the four types of shift registers based on applying inputs and accessing of outputs.

Serial In − Serial Out SISO???? Shift Register

The shift register, which allows serial input and produces serial output is known as Serial In – Serial Out SISO???? shift register. The block diagram of 3-bit SISO shift register is shown in the following figure.

This block diagram consists of three D flip-flops, which are cascaded. That means, output of one D flip-flop is connected as the input of next D flip-flop. All these flip-flops are synchronous with each other since, the same clock signal is applied to each one.

In this shift register, we can send the bits serially from the input of left most D flip-flop. Hence, this input is also called as serial input. For every positive edge triggering of clock signal, the data shifts from one stage to the next. So, we can receive the bits serially from the output of right most D flip-flop. Hence, this output is also called as serial output.

Example

Let us see the working of 3-bit SISO shift register by sending the binary information “011” from LSB to MSB serially at the input.

Assume, initial status of the D flip-flops from leftmost to rightmost is Q2Q1Q0=000?2?1?0=000. We can understand the working of 3-bit SISO shift register from the following table.

No of positive edge of Clock	Serial Input	Q₂	Q₁	Q₀
0	-	0	0	0
1	1LSB???	1	0	0
2	1	1	1	0
3	0MSB???	0	1	1LSB???
4	-	-	0	1
5	-	-	-	0MSB???

The initial status of the D flip-flops in the absence of clock signal is Q2Q1Q0=000?2?1?0=000. Here, the serial output is coming from Q0?0. So, the LSB 11 is received at 3^rd positive edge of clock and the MSB 00 is received at 5^th positive edge of clock.

Therefore, the 3-bit SISO shift register requires five clock pulses in order to produce the valid output. Similarly, the N-bit SISO shift register requires 2N-1 clock pulses in order to shift ‘N’ bit information.

Serial In - Parallel Out SIPO???? Shift Register

The shift register, which allows serial input and produces parallel output is known as Serial In – Parallel Out SIPO???? shift register. The block diagram of 3-bit SIPO shift register is shown in the following figure.

This circuit consists of three D flip-flops, which are cascaded. That means, output of one D flip-flop is connected as the input of next D flip-flop. All these flip-flops are synchronous with each other since, the same clock signal is applied to each one.

In this shift register, we can send the bits serially from the input of left most D flip-flop. Hence, this input is also called as serial input. For every positive edge triggering of clock signal, the data shifts from one stage to the next. In this case, we can access the outputs of each D flip-flop in parallel. So, we will get parallel outputs from this shift register.

Example

Let us see the working of 3-bit SIPO shift register by sending the binary information “011” from LSB to MSB serially at the input.

Assume, initial status of the D flip-flops from leftmost to rightmost is Q2Q1Q0=000?2?1?0=000. Here, Q2?2 & Q0?0 are MSB & LSB respectively. We can understand the working of 3-bit SIPO shift register from the following table.

No of positive edge of Clock	Serial Input	Q₂MSB???	Q₁	Q₀LSB???
0	-	0	0	0
1	1LSB???	1	0	0
2	1	1	1	0
3	0MSB???	0	1	1

The initial status of the D flip-flops in the absence of clock signal is Q2Q1Q0=000?2?1?0=000. The binary information “011” is obtained in parallel at the outputs of D flip-flops for third positive edge of clock.

So, the 3-bit SIPO shift register requires three clock pulses in order to produce the valid output. Similarly, the N-bit SIPO shift register requires N clock pulses in order to shift ‘N’ bit information.

Parallel In − Serial Out PISO???? Shift Register

The shift register, which allows parallel input and produces serial output is known as Parallel In − Serial Out PISO???? shift register. The block diagram of 3-bit PISO shift register is shown in the following figure.

In this shift register, we can apply the parallel inputs to each D flip-flop by making Preset Enable to 1. For every positive edge triggering of clock signal, the data shifts from one stage to the next. So, we will get the serial output from the right most D flip-flop.

Example

Let us see the working of 3-bit PISO shift register by applying the binary information “011” in parallel through preset inputs.

Since the preset inputs are applied before positive edge of Clock, the initial status of the D flip-flops from leftmost to rightmost will be Q2Q1Q0=011?2?1?0=011. We can understand the working of 3-bit PISO shift register from the following table.

No of positive edge of Clock	Q₂	Q₁	Q₀
0	0	1	1LSB???
1	-	0	1
2	-	-	0LSB???

Here, the serial output is coming from Q0?0. So, the LSB 11 is received before applying positive edge of clock and the MSB 00 is received at 2^nd positive edge of clock.

Therefore, the 3-bit PISO shift register requires two clock pulses in order to produce the valid output. Similarly, the N-bit PISO shift register requires N-1 clock pulses in order to shift ‘N’ bit information.

Parallel In - Parallel Out PIPO???? Shift Register

The shift register, which allows parallel input and produces parallel output is known as Parallel In − Parallel Out PIPO???? shift register. The block diagram of 3-bit PIPO shift register is shown in the following figure.

In this shift register, we can apply the parallel inputs to each D flip-flop by making Preset Enable to 1. We can apply the parallel inputs through preset or clear. These two are asynchronous inputs. That means, the flip-flops produce the corresponding outputs, based on the values of asynchronous inputs. In this case, the effect of outputs is independent of clock transition. So, we will get the parallel outputs from each D flip-flop.

Example

Let us see the working of 3-bit PIPO shift register by applying the binary information “011” in parallel through preset inputs.

Since the preset inputs are applied before positive edge of Clock, the initial status of the D flip-flops from leftmost to rightmost will be Q2Q1Q0=011?2?1?0=011. So, the binary information “011” is obtained in parallel at the outputs of D flip-flops before applying positive edge of clock.

Therefore, the 3-bit PIPO shift register requires zero clock pulses in order to produce the valid output. Similarly, the N-bit PIPO shift register doesn’t require any clock pulse in order to shift ‘N’ bit information.

Digital Circuits - Shift Registers